Short answer: type in the numbers from your test strip or lab report and the tool lines each one up against the EPA figure for that substance. EPA figures are of three kinds: enforceable limits (maximum contaminant levels), action levels that set off utility treatment steps, and secondary guidelines for taste, color and staining that are not enforceable. Hardness has no EPA limit, so it is shown against USGS’s classes.
Calculator
Compare your test values with EPA figures
Fill in only the values your strip or lab report gives. Each one is compared with the EPA figure listed in the table below, and the result names the kind of treatment EPA or the maker's manual links to that value. It does not say whether water is safe.
EPA figures and treatment types used
| Parameter | EPA figure | Kind of figure | Treatment type it points to | Sources |
|---|---|---|---|---|
| pH | 6.5 to 8.5 | Secondary guideline, not enforceable | not covered by our sources | EPA standard |
| Total hardness | none | No EPA limit | Water softener (NSF/ANSI 44) or a scale-reduction device (IAPMO/ANSI Z601) | EPA standard; EPA WaterSense guide, 'Why Soften Water?' |
| Free chlorine (as Cl2) | 4 mg/L | Disinfectant limit (MRDL) | Carbon filtration certified to NSF/ANSI 42 | EPA standard; EPA WaterSense guide, chlorine taste and odor |
| Nitrate (as nitrogen) | 10 mg/L as N | Primary limit (MCL) | Reverse osmosis certified to NSF/ANSI 58; EPA notes filters do not remove nitrate | EPA standard; EPA WaterSense guide, Table 2 |
| Nitrite (as nitrogen) | 1 mg/L as N | Primary limit (MCL) | Reverse osmosis certified to NSF/ANSI 58 | EPA standard; EPA WaterSense guide, Table 2 |
| Lead | 15 ug/L (ppb) | Action level | Point-of-use filter or reverse osmosis certified to NSF/ANSI 53 or 58 | EPA standard; EPA WaterSense guide, Tables 1 and 2 |
| Copper | 1.3 mg/L | Action level | not covered by our sources | EPA standard |
| Iron | 0.3 mg/L | Secondary guideline, not enforceable | A softener can reduce moderate dissolved (clear-water) iron; maker manuals add 5 grains of hardness per 1 ppm. It does not remove ferric (red-water) or bacterial iron | EPA standard; Whirlpool WHES48 owner's manual |
| Manganese | 0.05 mg/L | Secondary guideline, not enforceable | not covered by our sources | EPA standard |
| Total dissolved solids (TDS) | 500 mg/L (ppm) | Secondary guideline, not enforceable | Reverse osmosis (NSF/ANSI 58) or distillation (NSF/ANSI 62) reduce dissolved solids; carbon filters do not | EPA standard; EPA WaterSense guide, Table 2 |
| Chloride | 250 mg/L | Secondary guideline, not enforceable | not covered by our sources | EPA standard |
| Sulfate | 250 mg/L | Secondary guideline, not enforceable | not covered by our sources | EPA standard |
| Zinc | 5 mg/L | Secondary guideline, not enforceable | not covered by our sources | EPA standard |
| Fluoride | 4 mg/L | Primary limit (MCL) | not covered by our sources | EPA standard |
- EPA National Primary Drinking Water Regulations
- EPA Secondary Drinking Water Standards
- EPA WaterSense: Guide to Selecting Water Treatment Systems
- Whirlpool WHES48 owner's manual
- USGS: Hardness of water
EPA limits apply to public water systems. Private wells are not covered by them, but the numbers are still a useful yardstick. Last checked November 8, 2026.
Reading a strip or lab report
- Check the units. Strips often report nitrate as NO3, while the EPA limit is for nitrate as nitrogen. The tool converts if you choose the right basis. Lead is usually in parts per billion; most other values are mg/L, which equals ppm.
- Check the kit’s range. A strip can only show values within its printed range. A reading at the bottom or top of the scale may mean the real value is below or above it.
- TDS is a total, not a diagnosis. A TDS meter estimates dissolved solids from conductivity, so a reading of 200 ppm is an estimate of the total and does not say which minerals or contaminants make it up. Our TDS meter or multi-parameter kit comparison covers what each tool can show.
- Private wells. EPA’s limits are written for public systems. A well owner can still use them as a yardstick. For decisions about a well, use a certified lab. See our well water test panel guide .
From a value to a treatment type
The “treatment type” column names the category EPA’s WaterSense guide or a maker’s manual ties to the substance, such as a softener certified to NSF/ANSI 44 for hardness, carbon filtration certified to NSF/ANSI 42 for chlorine taste and odor, or reverse osmosis certified to NSF/ANSI 58 for nitrate. Where our sources do not name a treatment, the tool says so instead of guessing. Check the certification of any exact model with our certification guide and the filter finder . For results explained alongside a kit, see our test kit results guide .
Sources
- EPA National Primary Drinking Water Regulations
- EPA Secondary Drinking Water Standards
- EPA WaterSense: Guide to Selecting Water Treatment Systems
- USGS: Hardness of water
- Whirlpool WHES48 owner’s manual (iron and softeners)
Figures were checked on November 8, 2026. This is a comparison tool, not a medical or laboratory opinion.